石英玻璃的等离子体抛光技术研究现状

具有耐腐蚀、热膨胀系数低等诸多优良物理化学特性的石英玻璃在高性能光学系统中被广泛使用。要求元件达到纳米级别的表面粗糙度，而且没有损伤层和残余应力，因此精加工之后的超精密抛光工序尤为重要。本文介绍了气囊、磁流变、弹性发射、离子束等几种石英玻璃的精密抛光方法，侧重阐述了国内外等离子体的抛光技术，包括等离子体辅助化学刻蚀、等离子体喷射加工、等离子化学蒸发加工研究进展及取得的成果；且对等离子体的未来发展进行概述。     

基于等效电路模型与CDKF的锂离子电池荷电状态(SOC)估计

锂离子电池在社会生产各领域应用广泛,由于其复杂的电化学系统,状态检测难度较大,给供电保障带来不利影响.结合Thevenin等效电路与中心差分卡尔曼滤波法(CDKF),构建了一种聚合物锂离子电池的荷电状态(SOC)估计模型.MATLAB仿真验证表明,该模型能有效防止安时计数误差累积,电池SOC估计误差不超过5%.     

NiCrAl/Diatomite可磨耗封严涂层制备及性能

分别利用大气等离子喷涂技术制备了Ni/Al粘结底层、火焰喷涂技术制备了NiCrAl/Diatomite可磨耗封严涂层，研究了喷涂距离、送粉速率、火焰气体总流量、喷涂角度和氧燃比等喷涂参数对生长速率和涂层硬度的影响。结果表明，在较低的氧燃比条件下（O₂∶C₂H₂<1.6），随着喷涂距离的增大，涂层生长速率逐渐下降，硬度先保持不变后逐渐上升；当O₂∶C₂H₂>1.6时，涂层的生长速率会随着喷涂距离的增大先增大后减小，硬度随之逐渐下降。随着喷枪对基体相对移动速度的增大，涂层生长速率略微下降，硬度略有上升。气体总流量的增大使得涂层的生长速率明显上升，硬度明显下降。随着送粉量的增大，涂层生长速率明显提高，硬度随之先上升后下降。     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

磁场对高电压霍尔推力器性能影响研究

为研究磁场构型、磁场强度对高电压霍尔推力器主要性能的影响机理,以HET-200推力器为对象,采用固定磁场构型和不固定磁场构型两种方案进行实验研究。结果表明,在不固定构型的情况下增强磁场,放电电流存在两个极小值,效率也存在相应的两个极大值;但当固定磁场构型时,则放电电流只有一个最小值,效率也只有一个最大值。以最优效率下的磁场构型为基准,获得了磁场与电压、磁场与流量的匹配关系分别为B_(r, max)∝V~(0.7),B_(r, max)∝m。     

RTK model and positioning performance analysis using Galileo four-frequency observations

This paper proposes a real-time kinematic (RTK) model that uses one common reference satellite for the Galileo system with four frequency observations. In the proposed model, the double-differenced (DD) pseudorange and carrier phase biases among the different frequencies are estimated as unknown parameters to recover the integer features of the DD ambiguities among the different frequencies for ambiguity resolution and precise positioning. Analysis results show that the E5a, E5b, and E5 frequencies have virtually the same performance in terms of the positioning accuracy, observation residuals, and ratio values of ambiguity resolution. However, the E1 frequency performs worse than the E5a, E5b, and E5 frequencies. The RTK results for the combination of multiple frequencies are much better than those for a single-frequency observation, the coordinates’ standard deviation is improved about 20–30%, and the ambiguity fix time is improved about 10%.     

期望状态序列导向的深空探测器规划修复方法

Aiming at the challenges caused by the persistence, concurrency and energy consumption of probe actions, a plan repair method of deep space probe based on the expected state sequence is proposed. In this method, the expected state sequence is formed of the expected effect of the unfinished action and the expected precondition of the unexecuted action in the pre designed plan, according to the execution status of the action. The expected state sequence is an ordered set of states with mixed logic and energy, providing subgoals for plan repair and also transforming the plan repair problem into the state transition path searching problem. During the search, the plan repair strategy with energy supply priority is proposed, which separates the logic repair from energy repair to reduce the difficulty of solving the problem. And this method enables the probe to recover from plan failure autonomously. Finally, the effectiveness and rationality of the proposed method are verified through simulation by taking the Mars Orbiter as an example.     

速率模式飞轮姿态控制系统飞轮组合平稳切换方法

对速率模式飞轮姿态控制系统的能控性、稳定性和飞轮组合切换过程进行了研究，揭示了在飞轮组合切换过程中引起卫星姿态抖动的原因，提出了通过对残余角动量进行卸载并将卸载函数同时前馈到系统输入的方法，以保持卫星姿态的稳定度。从理论上证明了可引入残余角动量进行卸载，将卸载函数同时前馈到系统输入，并且不改变原系统的能控性和稳定性。给出了某卫星飞轮切换应用实例，说明了飞轮组合平稳切换方法的有效性。     

无人集群系统时变编队H∞控制

针对有向通信拓扑网络下具有通信时滞与外部干扰的无人集群系统（AUSS）时变编队H_∞控制问题进行了研究。首先，基于AUSS期望编队构型信息、无人机（UAV）实时状态信息以及通信UAV之间带通信时滞的状态误差信息提出了AUSS的编队控制方法，通过变量替换将AUSS的编队控制问题转换成低维闭环系统的渐近稳定问题，并以线性矩阵不等式（LMI）形式给出了系统稳定的充分条件与最大允许通信时滞的计算公式。其次，通过构造Lyapunov-Krasovskii（L-K）泛函，证明了存在通信时滞与外部干扰条件下AUSS能够实现时变编队。最后，通过数值仿真验证所设计方法的准确性与有效性。